Cisco Usb Console Driver X64

Installing and Connecting the Router This document describes how to install and connect Cisco 2900 series and Cisco 3900 series integrated services routers (ISRs) to LAN, WAN, and Voice networks. The following sections provide technical details.

• • • • • • • • • • • • Installation Requirements and Warnings Warning qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Warning This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028 Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029 Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports.

When detaching cables, detach the end away from the unit first. Statement 1026 Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor.

Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024 Warning Before opening the unit, disconnect the telephone-network cables to avoid contact with telephone-network voltages.

Statement 1041 Warning Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Statement 1035 Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Statement 1036 Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

Anyone ever had problems using windows 8.1 with the appropriate 64bit windows driver installed, using a console USB cable and trying to connect to a switch via serial. Tried both Com1 and Com3. Get an older laptop with windows 7 and it works no worries with same cable, and driver. View and Download Cisco Catalyst 3560-C hardware installation manual online. Catalyst 3560-C Switch pdf manual download.

Statement 1037 Warning Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Statement 1038 Warning To report a gas leak, do not use a telephone in the vicinity of the leak. Statement 1039 Warning This unit is intended for installation in restricted access areas.

A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. Statement 1017 Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029 Warning The covers are an integral part of the safety design of the product. Do not operate the unit without the covers installed.

Statement 1077 What you Need to Know CLI Console Access Use the new USB console port on the router to access the Cisco Internet Operating System (IOS) CLI on the router and perform configuration tasks. A terminal emulation program, such as Microsoft Windows HyperTerminal, is required to establish communication between the router and a PC. See the for instructions. Note A Microsoft Windows USB driver must be installed before you establish physical connectivity between the router and the PC.

Slot and Port Numbers Cisco 2900 series and 3900 series ISRs have built in ports and new slots. The new slots accommodate new modules and interface cards; Enhanced High-Speed WAN Interface Cards (EHWICs), Internal Services Modules (ISMs), Packet Voice Data Modules (PVDM3), and Service Modules (SMs).

See the for slot and port numbering. Software Licenses To use the following features on Cisco Integrated Services Routers, you must purchase a software package. • Gatekeeper • IPS (subscription) • SSL_VPN (counted) • SNA Switching See the for more information. Before you Begin Before installing and connecting a Cisco Integrated Services Router, read the safety warnings and gather the following tools and equipment. • ESD-preventive cord and wrist strap • Number 2 Phillips screwdriver • Flat-blade screwdrivers: small, 3/16-in.

(4 to 5 mm) and medium, 1/4-in. (6 to 7 mm) – To install or remove modules – To remove the cover, if you are upgrading memory or other components • Screws that fit your rack • Wire crimper • Wire for connecting the chassis to an earth ground: – AWG 6 (13 mm 2) wire for NEBS-compliant chassis grounding – AWG 14 (2 mm 2) or larger wire for NEC-compliant chassis grounding – AWG 18 (1 mm 2) or larger wire for EN/IEC 60950-compliant chassis grounding • For NEC-compliant grounding, an appropriate user-supplied ring terminal, with an inner diameter of 1/4 in. (5 to 7 mm) In addition, depending on the type of modules you plan to use, you might need the following equipment to connect a port to an external network: • Cables for connection to the WAN and LAN ports (dependent on configuration) Note For more information on cable specifications, see the on Cisco.com. • Ethernet hub or PC with a network interface card for connection to an Ethernet (LAN) port. • Console terminal (an ASCII terminal or a PC running HyperTerminal or similar terminal emulation software) configured for 9600 baud, 8 data bits, 1 stop bit, no flow control, and no parity. • Modem for connection to the auxiliary port for remote administrative access (optional).

• Data service unit (DSU) or channel service unit/data service unit (CSU/DSU) as appropriate for serial interfaces. • External CSU for any CT1/PRI modules without a built-in CSU. • NT1 device for ISDN BRI S/T interfaces (if not supplied by your service provider). Unpacking the Router Do not unpack the router until you are ready to install it.

If the final installation site will not be ready for some time, keep the chassis in its shipping container to prevent accidental damage. When you are ready to install the router, proceed with unpacking it.

The router, accessory kit, publications, and any optional equipment you ordered may be shipped in more than one container. When you unpack the containers, check the packing list to ensure that you received all of the items on the list. Installing the Router If you need to install service modules, interface cards, and FRUs, you can install them either before or after you install the router. Ideally, you install modules and interface cards when you have the best access to the back panel of the router. Internal modules and FRUs, such as internal services modules (ISMs) or packet voice data modules (PVDMs), and fan trays should be installed before rack-mounting. There are three methods of installing the router: • • • Warning Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord. Statement 1 Caution To prevent damage to the chassis, never attempt to lift or tilt the chassis by holding it by the plastic panel on the front.

Always hold the chassis by the sides of the metal body. Rack-Mounting the Chassis Cisco 2900 series and 3900 series routers can be installed in 19-inch (48.26-cm) EIA and 23-inch (58.42-cm) Southwestern Bell Corporation (SBC) racks. The Cisco 3900 series routers can also be mounted in a 600-mm ETSI rack. Use the standard brackets shipped with the router for mounting the chassis in a 19-inch EIA rack; you can order optional larger brackets for mounting the chassis in a 19-inch SBC rack. You can mount the router in the following ways: • Center-front mounting—Brackets attached in the center front of the chassis with only the front panel facing forward.

• Center-back mounting—Brackets attached in the center back of the chassis with only the back panel facing forward. • Front mounting—Brackets attached at the front of the chassis with the front panel facing forward. • Back mounting—Brackets attached at the back of the chassis with the back panel facing forward. Attaching Rack-Mount Brackets to Cisco 2901 Routers For the Cisco 2900 series routers use four of the supplied number-8 Phillips flat-head screws to attach the long side of each bracket to the router. For the Cisco 3900 series routers use four of the supplied number-6 Phillips flat-head screws to attach the long side of each bracket to the router.

Shows how to attach the brackets to the sides of the router with the front panel forward. Figure 3-1 Bracket Installation for Front Mounting shows how to attach the brackets to the sides of the router with the back panel forward. Figure 3-2 Bracket Installation for Back Mounting shows how to attach the brackets to the sides of the router with center mounting. Figure 3-3 Bracket Installation for Center Mounting Attaching Rack-Mount Brackets to Cisco 2911, Cisco 2921, and Cisco 2951 Routers Attach the mounting brackets to the router chassis as shown in through, using the screws provided. Caution Do not over torque the screws. The recommended torque is 15 to 18 inch-lb (1.7 to 2.0 N-m).

Attach the second bracket to the opposite side of the chassis. Use a number-2 Phillips screwdriver to install the number-8 bracket screws. Caution Your chassis installation must allow unrestricted airflow for chassis cooling.

Figure 3-4 Bracket Installation for Front Mounting 1 23-inch SBC brackets 2 19-inch EIA brackets 1.Southwestern Bell Corporation (SBC) Figure 3-5 Bracket Installation for Center-Front Mounting 1 23-inch SBC brackets 2 19-inch EIA brackets Figure 3-6 Bracket Installation for Back Mounting 1 23-inch SBC brackets 2 19-inch EIA brackets Figure 3-7 Bracket Installation for Center-Back Mounting 1 23-inch SBC brackets 2 19-inch EIA brackets Attaching Rack-Mount Brackets to Cisco 3900 Series Routers Attach the mounting brackets to the router chassis as shown in through, using the screws provided. Caution Do not over torque the screws. The recommended torque is 8 to 10 inch-lb (0.9 to 1.12 N-m). Attach the second bracket to the opposite side of the chassis. Use a number-2 Phillips screwdriver to install the number-6 bracket screws. Caution Your chassis installation must allow unrestricted airflow for chassis cooling. Figure 3-8 Bracket Installation for Front Mounting 1 23-inch EIA brackets 2 19-inch EIA brackets Figure 3-9 Bracket Installation for Center-Front Mounting 1 23-inch EIA brackets 2 19-inch EIA brackets Figure 3-10 Bracket Installation for Rear Mounting 1 23-inch EIA brackets 2 19-inch EIA brackets Figure 3-11 Bracket Installation for Center-Rear Mounting 1 23-inch EIA brackets 2 19-inch EIA brackets Mounting the Router in a Rack After you attach the rack-mount brackets to the router chassis, use the screws provided with the rack to install the chassis in the rack.

(See.) Tip For 23-inch SBC brackets start the lower pair of screws first, and rest the brackets on the lower screws while you insert the upper pair of screws. Tip The screw slots in the brackets are spaced to line up with every second pair of screw holes in the rack. When the correct screw holes are used, the small threaded holes in the brackets line up with unused screw holes in the rack.

If the small holes do not line up with the rack holes, you must raise or lower the brackets to the next rack hole. Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: • This unit should be mounted at the bottom of the rack if it is the only unit in the rack. • When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. • If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.

Statement 1006 Warning To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the handles on modules (such as power supplies, fans, or cards); these types of handles are not designed to support the weight of the unit. Statement 1032 Caution Be sure to leave space above and below each router in a rack to allow for cooling air circulation.

Shows a typical installation in a rack. Figure 3-12 Mounting the Chassis in a Rack (Typical) 1 Mounting screws (4) shows an installation with a chassis rear-forward. Figure 3-13 Mounting the Chassis in a Rack, Rear Forward 1 Mounting screws (4) Grounding the Chassis After the router is installed, you must connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the.

Setting the Chassis on a Desktop You can place Cisco 2901, Cisco 2911, and Cisco 3900 series routers on a desktop or shelf. Note Models 2921 and above are not recommended for desktop mounting.

To install a Cisco 2901 or 2911 router on a desktop, first install the four rubber feet that are supplied in the accessory kit. They provide anti-skid protection and space for air circulation. Peel the rubber feet from the adhesive strip, and stick them onto the “+” marked on the bottom of the chassis. Warning To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the handles on modules (such as power supplies, fans, or cards); these types of handles are not designed to support the weight of the unit. Statement 1032 Caution Do not place anything on top of the router that weighs more than 10 pounds (4.5 kg), and do not stack routers on a desktop. Excessive distributed weight of more than 10 pounds, or pound point load of 10 pounds on top could damage the chassis. Caution Your chassis installation must allow unrestricted airflow for chassis cooling.

For placing the router on a desktop, keep at least 1 inch (2.54 cm) of clear space beside the cooling inlet and exhaust vents. After the router is installed, you must connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the. Mounting a Cisco 2901 or 2911 Router on a Wall This section explains how to mount Cisco 2901 and Cisco 2911 routers on a wall or other vertical surface. We do not recommend mounting a Cisco 2921, 2951, or Cisco 3900 series router on a wall.

The following warning applies to Cisco 2901 and 2911 routers: Warning This unit is intended to be mounted on a wall. Please read the wall mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 248 Tip When choosing a wall-mounting location, consider cable limitations and wall structure.

Note The Cisco 2901 and Cisco 2911 routers use brackets designed for the 19-inch EIA rack-mounting, the part number 700-16559-01 is stamped on the bracket (shown in ). Attaching Brackets to the Router for Wall Mounting Attach the standard brackets to the chassis using the four screws provided for each bracket. Attaching the Router to a Wall Attach the router to the wall using the brackets previously attached. Use attachment hardware that you provide as follows: • For attaching to a wall stud, each bracket requires two number-10 wood screws (round- or pan-head) with number-10 washers, or two number-10 washer-head screws. The screws must be long enough to penetrate at least 1.5 inches (38.1 mm) into the supporting wood or metal wall stud. • For hollow-wall mounting, each bracket requires two wall anchors with washers. Wall anchors and washers must be size number 10.

• Route the cables so that they do not put a strain on the connectors or mounting hardware. • The NEBS air baffle (Cisco 2911) should not be used when wall-mounting the router. Caution This unit is intended to be mounted on a wall. Please read the wall mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Caution The router must be mounted with the power connections oriented downward. Failure to do so could present a fire hazard.

And show typical wall-mounted installations. Figure 3-14 Mounting the 2901 Chassis on the Wall Figure 3-15 Mounting the 2911 Chassis on the Wall After the router is installed, you must connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the. Chassis Grounding Warning This equipment must be grounded.

Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024 Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, you could shock yourself. Statement 94 You must connect the chassis to a reliable earth ground; the ground wire must be installed in accordance with local electrical safety standards.

• For NEBS-compliant grounding, use size 6 AWG (13 mm 2) copper wire and the ground lug provided in the accessory kit. Note NEBS-compliant grounding is not supported on the Cisco 2901 router. Note This equipment is suitable for installation in Network Telecommunications Facilities and locations where the NEC applies. The equipment is suitable for installation as part of the Common Bonding Network (CBN). • For NEC-compliant grounding, use size 14 AWG (2 mm 2) or larger copper wire and an appropriate user-supplied ring terminal with an inner diameter of 1/4 in. • For EN/IEC 60950-compliant grounding, use size 18 AWG (1 mm 2) or larger copper wire and an appropriate user-supplied ring terminal.

To install the ground connection for a Cisco 2900 or Cisco 3900 series router, perform the following steps: Step 1 Strip one end of the ground wire to the length required for the ground lug or terminal. • For the NEBS ground lug—approximately 0.75 inch (20 mm) • For user-provided ring terminal—as required Step 2 Crimp the ground wire to the ground lug or ring terminal, using a crimp tool of the appropriate size. Step 3 Attach the ground lug or ring terminal to the chassis as shown in,,,,.

For a ground lug, use the two screws with captive locking washers provided. For a ring terminal, use one of the screws provided. Tighten the screws to a torque of 8 to 10 in-lb (0.9 to 1.1 N-m). Figure 3-16 Chassis Ground Connection Using Ring Terminal on Cisco 2901 Chassis Figure 3-17 NEBS-Compliant Chassis Ground Connection on Cisco 2911 Chassis Figure 3-18 NEBS-Compliant Chassis Ground Connection on Cisco 2921 or Cisco 2951 Chassis Figure 3-19 Chassis Ground Connection on Cisco 3900 Series Chassis Step 4 Connect the other end of the ground wire to a known reliable earth ground point at your site. Connecting Power This section explains how to connect AC or DC power to Cisco 2900 series routers.

It covers the following topics: • • • Warning Read the installation instructions before connecting the system to the power source. Statement 1004 Warning This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Note The installation must comply with all required electrical codes applicable at the installation site.

Connecting to AC Power If your router uses AC power, connect it to a 15 A, 120 VAC (10 A, 240 VAC) circuit with overcurrent protection. If backup power is required, see the. Note The input voltage tolerance limits for AC power are 90 and 264 VAC. Note This product requires surge protection to be provided as part of the building installation. To comply with the Telcordia GR-1089 NEBS standard for electromagnetic compatibility and safety, an external surge protective device (SPD) is required at the AC power service equipment. Warning AC connected units must have a permanent ground connection in addition to the power cable ground wire. NEBS-compliant grounding satisfies this requirement.

Statement 284 Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations. Statement 1045 Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 15A, 120VAC (16A, 240VAC).

Statement 1005 Connecting to DC Power If your router has a DC-input power supply, follow the directions in this section for proper wiring. A router with a DC-input power supply has a terminal block for the DC power connections. If backup power is required, see the section. • • • • Caution DC return is isolated from the frame.

(NEBS DC-I) Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations. Statement 1045 Warning This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 60 VDC, 20 A. Statement 1005 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Warning Use copper conductors only.

Statement 1025 DC Wiring Requirements for Cisco 2911, 2921, and 2951 Routers A Cisco 2911, Cisco 2921, or Cisco 2951 router with a DC-input power supply requires copper wire and crimp-type terminals for the power connections. And summarize the wiring requirements. You can connect a single DC power source to either the A input or the B input. If there are dual power sources, connect one source to the A input and one source to the B input; both sources must be the same polarity and voltage. Table 3-1 DC Wiring Requirements for Cisco 2911 Routers DC Power Input DC Input Wire Size Safety Ground Wire Size Wire Terminal (Lug) Overcurrent Protection 24-36 VDC, 11 A, positive or negative, single source or dual sources AWG 14 (2.0 mm 2) AWG 14 (2.0 mm 2), minimum Amp/Tyco No. 32957 20 A maximum 36-60 VDC, 4 A, positive or negative, single source or dual sources Table 3-2 DC Wiring Requirements for Cisco 2921 and 2951 Routers DC Power Input DC Input Wire Size Safety Ground Wire Size Wire Terminal (Lug) Overcurrent Protection 24-36 VDC, 17 A, positive or negative, single source or dual sources AWG 14 (2.0 mm 2) AWG 14 (2.0 mm 2), minimum Amp/Tyco No.

32957 20 A maximum 36-60 VDC, 7 A, positive or negative, single source or dual sources Wiring Procedure for DC Input on Cisco 2911, 2921, and 2951 Routers To connect a router to a DC power source, perform the following steps: Step 1 Remove power from the DC circuit. To ensure that power is removed from the DC circuit, locate the circuit breaker for the DC circuit, switch the circuit breaker to the OFF position. Warning Follow proper Lockout /Tagout Procedures as defined by your company in accordance with local and national laws (e.g. Title 29 CFR Part 1910.147).

Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. Statement 1003 Warning Use copper conductors only. Statement 1025 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Tip Tip Secure all power cabling when installing this unit to avoid disturbing field-wiring connections.

Warning When stranded wiring is required, use approved wiring terminations, such as closed-loop or spade-type with upturned lugs. These terminations should be the appropriate size for the wires and should clamp both the insulation and conductor. Statement 1002 Step 2 Strip the wires to the appropriate length for the terminals. The strip length is 5/64 to 1/8 inch (2 to 4 mm) for Amp/Tyco No. 32957 terminals.

Step 3 Crimp the terminals to the power input and safety ground wires. Step 4 Remove the plastic covers from the terminal block. Save the covers for reinstallation after you finish wiring. Step 5 Connect the wires to the terminal block, starting with the safety ground wire.

Connect each wire to the appropriate terminal as shown in Figure 1. Tighten the terminal screws to 8.0 ± 0.5 in-lb (0.9 ± 0.05 N-m). Warning This unit might have more than one power supply connection.

All connections must be removed to de-energize the unit. Statement 1028 Warning The illustration shows the DC power supply terminal block. Wire the DC power supply as illustrated. The proper wiring sequence is ground to ground, positive to positive, and negative to negative. The ground wire should always be connected first and disconnected last. Statement 239 Warning An exposed wire lead from a DC-input power source can conduct harmful levels of electricity. Be sure that no exposed portion of the DC-input power source wire extends from the terminal block plug.

Statement 122 Caution Dual sources with opposite-polarity grounding damage equipment. Caution Caution Do not overtorque the terminal block contact screws.

Recommended torque is 5.0 ± 0.5 in-lb (0.56 ± 0.06 N-m) for 2911 series routers, and 9 ± 1.0 in-lb (1.02 ± 0.11 N-m) Figure 3-20 DC Power Connections for Cisco 2911, 2921, and 2951 Routers Step 6 Install the plastic covers over the terminals. (See or.) Warning The safety cover is an integral part of the product. Do not operate the unit without the safety cover installed. Operating the unit without the cover in place will invalidate the safety approvals and pose a risk of fire and electrical hazards. Statement 117 Step 7 Organize and secure the wires using cable ties as shown in Figure 2 or Figure 3.

Make sure that the wires do not project above or below the front panel of the router. Step 8 Turn on power to the DC circuit. Be sure to remove tape used to secure the circuit-breaker switch in the OFF position.

Figure 3-21 Wire Routing and Attachment for Cisco 2911 Routers Figure 3-22 Wire Routing and Attachment for Cisco 2921 and Cisco 2951 Routers Approved Scenarios and Scenarios Not Approved for Dual DC Power Supply Configuration on Cisco 2911, 2921, and 2951 Routers You can connect a single DC power source to either the A input or the B input. If there are dual power sources, connect one source to the A input and one source to the B input. Both sources must be the same polarity (with respect to ground) and voltage (within 0.25 volts). Do not connect –DC grounded and +DC grounded dual sources to Cisco 2911, Cisco 2921, and Cisco 2951 routers.

Caution Dual sources with opposite-polarity grounding damage equipment. In, either the positive source terminal or the negative source terminal is tied to ground.

Figure 3-23 Connecting to One Source Only—Source A or Source B In, source A and source B share common negative terminal connections. Figure 3-24 Connecting Source A and Source B with Common Negative Terminals DC Wiring Requirements for Cisco 3900 Series Routers If your router has a DC-input power supply, follow the directions in this section for proper wiring.

If backup power is required, see the section. Warning Use copper conductors only.

Statement 1025 Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations.

Statement 1045 The following warning applies to the Cisco 3925 and Cisco 3925-NOVPN routers only: Warning This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 60 VDC, 20 A. Statement 1005 The following warning applies to the Cisco 3945 and Cisco 3945-NOVPN routers only: Warning This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 60 VDC, 30 A. Statement 1005 Warning This unit might have more than one power supply connection.

All connections must be removed to de-energize the unit. Statement 1028 summarizes DC wiring requirements for all Cisco 3925 and Cisco 3945 routers.

Note For Cisco 3945 and Cisco 3945-NOVPN routers, the safety ground wire connection must be at the same potential as the 0 V (return) connection. Table 3-3 DC Wiring Requirements for Cisco 3900 DC Power Input DC Input Wire Size Safety Ground Wire Size Wire Terminal (Lug) Overcurrent Protection 24-36 VDC, 12 A, positive or negative, single source or dual sources AWG 10 AWG 10 minimum Panduit No. LCAS8-10F-L 30 A maximum 36-60 VDC, 8 A, positive or negative, single or dual source Cisco 3900 Series Router Wiring Procedure for DC Input To connect the router to a DC power source, follow these steps: Step 1 Remove power from the DC circuit. To ensure that power is removed from the DC circuit, locate the circuit breaker for the DC circuit, switch the circuit breaker to the OFF position. Warning Follow proper Lockout /Tagout Procedures as defined by your company in accordance with local and national laws (e.g.

Title 29 CFR Part 1910.147). Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. Statement 1003 Tip Secure all power cabling when installing this unit to avoid disturbing field-wiring connections.

Warning When stranded wiring is required, use approved wiring terminations, such as closed-loop or spade-type with upturned lugs. These terminations should be the appropriate size for the wires and should clamp both the insulation and conductor. Statement 1002 Step 2 Strip the wires to the appropriate length for the terminals.

The length is 3/16 to 1/4 inch (5 to 6 mm) for Panduit No. LCAS8-10F-L terminals. Step 3 Crimp the terminals onto the DC power input and safety ground wires. Step 4 Remove the plastic covers from the terminal block. Save the covers for reinstallation after you finish wiring.

Step 5 Connect the wires to the terminal block, starting with the safety ground wire. Connect each wire to the appropriate terminal as shown in. Warning The illustration shows the DC power supply terminal block. Wire the DC power supply as illustrated. The proper wiring sequence is ground to ground, positive to positive, and negative to negative. The ground wire should always be connected first and disconnected last. Statement 239 Warning An exposed wire lead from a DC-input power source can conduct harmful levels of electricity.

Be sure that no exposed portion of the DC-input power source wire extends from the terminal block plug. Statement 122 Caution Do not overtorque the terminal block screws. The recommended torque is 18.0 – 20.0 in-lb (2.03 – 2.26 N-m). Figure 3-25 DC Power Connections for Cisco 3925 and 3925-NOVPN Routers Figure 3-26 DC Power Connections for the Cisco 3945 and 3945-NOVPN Routers Step 6 Install the plastic cover over the terminals. (See.) Warning The safety cover is an integral part of the product.

Do not operate the unit without the safety cover installed. Operating the unit without the cover in place will invalidate the safety approvals and pose a risk of fire and electrical hazards. Statement 117 Step 7 Organize and bundle the wires using cable ties as shown in. Step 8 If you are installing a second DC power supply, repeat Step 1 through Step 7 for the second supply (input B).

Step 9 Turn on power to the DC circuit. Be sure to remove tape used to secure the circuit-breaker switch in the OFF position. Figure 3-27 DC Wire Routing andAttachment for Cisco 3925 and 3925-NOVPN Router Figure 3-28 DC Wire Routing and Attachment for Cisco 3945 and 3945-NOVPN Router Dual DC Power Supply Configuration in Cisco 3925 and Cisco 3925-NOVPN Routers You can connect a single DC power source to either the A input or the B input. If there are dual power sources, connect one source to the A input and one source to the B input. Both sources must have the same polarity (with respect to ground) and voltage (within 0.25 V). Do not connect -DC-grounded and +DC-grounded dual sources to Cisco 3925 and Cisco 3925-NOVPN routers.

Caution Dual sources with opposite-polarity grounding damage equipment. In, either the positive source terminal or the negative source terminal is tied to ground. Figure 3-29 Connecting to One Source Only—Source A or Source B In, source A and source B share common negative terminal connections. Figure 3-30 Connecting Source A and Source B with Common Negative Terminals Connecting to Backup Power The redundant power supply (RPS) for the Cisco 2911, Cisco 2921, and Cisco 2951 router is an external Cisco RPS 2300. To connect the RPS, the router must be fitted with an RPS adapter. See the before connecting to a backup power source. Caution Before connecting the RPS to the router, make sure that either the RPS is in standby mode or the RPS AC power is disconnected.

Connecting the RPS to AC power automatically places the RPS in active mode. Note The Cisco 2901 router does not support an RPS. Connecting to a Console Terminal or Modem The router has asynchronous serial ports and auxiliary ports. These ports provide administrative access to the router either locally (with a console terminal or a PC) or remotely (with a modem).To configure the router through the Cisco IOS CLI, you must establish a connection between the router console port and either a terminal or a PC. Use the following cables and adapters to establish a local or remote connection. Table 3-4 Local and Remote Connections Port Type Cable Section Serial (RJ-45) EIA RJ-45 Serial (USB) USB 5-pin mini USB Type-B-to-USB Type-A Auxiliary (Modem) DB-9-to-DB-25 Connecting to the Serial Port with Microsoft Windows Note Install the USB device driver before establishing a physical connection between the router and the PC using the USB Console cable plugged into the USB serial port, otherwise the connection will fail. Step 1 Connect the end of the console cable with the RJ-45 connector to the light blue console port on the router.

Or Connect a USB 5-pin mini USB Type-B to the USB console port as shown in,. If you are using the USB serial port for the first time on a Windows-based PC, install the USB driver now according to the instructions in the following sections. • • • Note You cannot use the USB port and the EIA port concurrently.

When the USB port is used it takes priority over the RJ-45 EIA port. Step 2 Connect the end of the cable with the DB-9 connector (or USB Type-A) to the terminal or PC. If your terminal or PC has a console port that does not accommodate a DB-9 connector, you must provide an appropriate adapter for that port. Step 3 To communicate with the router, start a terminal emulator application, such as Microsoft Windows HyperTerminal.

Configuring the Switch with the CLI-Based Setup Program This appendix provides a CLI-based setup procedure for a Catalyst 2960-S standalone switch or a switch stack. Before you turn on the switch power, review the safety warnings in Accessing the CLI Through Express Setup You can access the CLI on an unconfigured switch. Set the switch in Express Setup mode and connect a switch Ethernet port to an Ethernet port on your PC or workstation. Follow the steps described in the getting started guide for turning on the switch and using Express Setup. When the switch is in Express Setup mode, open a Telnet session to the switch by entering the IP address 10.0.0.1. Enter the setup user EXEC command.

Enter the information described in the and the. After you have entered the configuration information for the switch, save it to flash memory by using the write memory privileged EXEC command.

Note In Express Setup mode, the IP address 10.0.0.1 remains active on the switch until you enter the write memory command. You lose the Telnet connection after entering the write memory command. For information about using the CLI, see the switch command reference for this release. Accessing the CLI Through the Console Port You can access the CLI on a configured or unconfigured switch by connecting the RJ-45 console port or USB console port of the switch to your PC or workstation and accessing the switch through a terminal emulation program.

Note If you have stacked your switches, connect to the console port of one of the switches in the stack. You can initially configure the entire stack from any member switch. Connecting the RJ-45 Console Port or USB Console Port Step 1 If you are connecting the switch USB console port to a Windows-based PC for the first time, install the USB driver according to these instructions. • • • Note If you do not want to use the switch USB console port, you can use an RJ-45-to-DB-9 adapter cable to connect the switch RJ-45 console port to a PC or terminal port. Figure C-1 Connecting the USB Console Cable to the Catalyst 2960-S Switch 1 USB console port (5-pin mini-Type B) 2 USB Type A to 5-pin mini-Type B cable 3 USB Type A connection on laptop Step 2 Start the terminal-emulation program on the PC or the terminal.

The program, frequently a PC application such as HyperTerminal or ProcommPlus, makes communication between the switch and your PC or terminal possible. Step 3 Configure the baud rate and character format of the PC or terminal to match the console port default characteristics: • 9600 baud • 8 data bits • 1 stop bit • No parity • None (flow control) Step 4 Power on the switch as described in the switch getting started guide. Step 5 The PC or terminal displays the bootloader sequence.

Press Enter to display the setup prompt. Follow the steps in the. Installing the Cisco Microsoft Windows USB Device Driver A USB device driver must be installed the first time a Microsoft Windows-based PC is connected to the switch USB console port. Installing the Cisco Microsoft Windows XP USB Driver Step 1 Obtain the file Cisco_usbconsole_driver.zip from the Cisco.com web site and unzip it. Note You can download the driver file from the Cisco.com site where you download the switch software. Step 2 If using 32-bit Windows XP, double-click the file setup.exe from the Windows_32 folder. If using 64-bit Windows XP, double-click the file setup(x64). Canon Type Star 10 Manual. exe from the Windows_64 folder.

Step 3 The Cisco Virtual Com InstallShield Wizard begins. Step 4 The Ready to Install the Program window appears, Click Install. Step 5 The InstallShield Wizard Completed window appears.

Click Finish. Step 6 Connect the USB cable to the PC and switch console port. The LED for the USB console port turns green (see ), and within a few seconds a series of Found New Hardware Wizard windows appear. Follow the instructions to complete the driver installation.

The USB console is ready for use. Installing the Cisco Microsoft Windows 2000 USB Driver Step 1 Obtain the file Cisco_usbconsole_driver.zip from the Cisco.com web site and unzip it. Note You can download the driver file from the Cisco.com site where you download the switch software. Step 2 Double-click the file setup.exe. Step 3 The Cisco Virtual Com InstallShield Wizard begins. Step 4 The Ready to Install the Program window appears, Click Install. Step 5 The InstallShield Wizard Completed window appears.

Click Finish. Step 6 Connect the USB cable to the PC and switch console port. The LED for the USB console port turns green (see ), and within a few seconds a series of Found New Hardware Wizard windows appear. Follow the instructions to complete the driver installation. The USB console is ready for use. Installing the Cisco Microsoft Windows Vista USB Driver Step 1 Obtain the file Cisco_usbconsole_driver.zip from the Cisco.com web site and unzip it.

Note You can download the driver file from the Cisco.com site where you download the switch software. Step 2 If using 32-bit Windows Vista, double-click the file setup.exe from the Windows_32 folder. If using 64-bit Windows Vista, double-click the file setup(x64).exe from the Windows_64 folder. Step 3 The Cisco Virtual Com InstallShield Wizard begins. Step 4 The Ready to Install the Program window appears, Click Install. Note If a User Account Control warning appears, click 'Allow - I trust this program.' Step 5 The InstallShield Wizard Completed window appears.

Click Finish. Step 6 Connect the USB cable to the PC and the switch console port. The LED for the USB console port turns green (see ), and within a few seconds a series of Found New Hardware Wizard windows appear. Follow the instructions to complete the driver installation. The USB console is ready for use.

Uninstalling the Cisco Microsoft Windows USB Driver Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver The driver can be removed using the Windows Add or Remove Programs utility or the setup.exe program. Using the Add or Remove Programs Utility Note Disconnect the switch console terminal before uninstalling the driver. Step 1 Click Start >Control Panel >Add or Remove Programs. Step 2 Scroll to Cisco Virtual Com and click Remove. Step 3 When the Program Maintenance window appears, select the Remove radio button. Using the Setup.exe Program Note Disconnect the switch console terminal before uninstalling the driver.

Step 1 Run setup.exe for Windows 32-bit or setup(x64).exe for Windows-64bit. Step 2 The InstallShield Wizard for Cisco Virtual Com appears. Step 3 When the Program Maintenance window appears, select the Remove radio button. Step 4 When the Remove the Program window appears, click Remove. Step 5 When the InstallShield Wizard Completed window appears, click Finish. Uninstalling the Cisco Microsoft Windows Vista USB Driver Note Disconnect the switch console terminal before uninstalling the driver.

Step 1 Run the setup.exe for Windows 32-bit or setup(x64).exe for Windows-64bit. Step 2 The InstallShield Wizard for Cisco Virtual Com appears. Step 3 When the Program Maintenance window appears, select the Remove radio button. Step 4 When the Remove the Program window appears, click Remove. Step 5 If a User Account Control warning appears, click 'Allow - I trust this program.'

Step 6 When the InstallShield Wizard Completed window appears, click Finish. Entering the Initial Configuration Information To set up the switch, you need to complete the setup program, which runs automatically after the switch is powered on. You must assign an IP address and other configuration information necessary for the switch to communicate with the local routers and the Internet.

This information is also needed to use the device manager or Cisco Network Assistant to configure and manage the switch. IP Settings Obtain this information from your network administrator before you start the setup program: • Switch IP address • Subnet mask (IP netmask) • Default gateway (router) • Enable secret password • Enable password • Telnet password Completing the Setup Program If your switches are stacked and there are multiple console connections to individual switches in the stack, the initial setup dialog appears at the console where you first press Enter. Step 1 Enter Yes at these two prompts. Would you like to enter the initial configuration dialog?

[yes/no]: yes At any point you may enter a question mark '?' Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system. Would you like to enter basic management setup? [yes/no]: yes Step 2 Enter a host name for the switch, and press Return.

On a command switch, the host name is limited to 28 characters; on a member switch to 31 characters. Do not use -n, where n is a number, as the last character in a host name for any switch. Enter host name [Switch]: host_name Step 3 Enter an enable secret password, and press Return.

The password can be from 1 to 25 alphanumeric characters, can start with a number, is case sensitive, allows spaces, but ignores leading spaces. The secret password is encrypted, and the enable password is in plain text. Enter enable secret: secret_password Step 4 Enter an enable password, and press Return. Enter enable password: enable_password Step 5 Enter a virtual terminal (Telnet) password, and press Return. The password can be from 1 to 25 alphanumeric characters, is case sensitive, allows spaces, but ignores leading spaces. Enter virtual terminal password: terminal-password Step 6 (Optional) Configure Simple Network Management Protocol (SNMP) by responding to the prompts. You can also configure SNMP later through the CLI, the device manager, or the Network Assistant application.

To configure SNMP later, enter no. Configure SNMP Network Management? [no]: no Step 7 Enter the interface name (physical interface or VLAN name) of the connection to the management network, and press Return. For this release, always use vlan1 as that interface. Enter interface name used to connect to the management network from the above interface summary: vlan1 Step 8 Configure the interface by entering the switch IP address and subnet mask and pressing Return.

The IP address and subnet masks shown are examples. Configuring interface vlan1: Configure IP on this interface? [yes]: yes IP address for this interface: 10.4.120.106 Subnet mask for this interface [255.0.0.0]: 255.0.0.0 Step 9 Enter Y to configure the switch as the cluster command switch. Enter N to configure it as a member switch or as a standalone switch.

If you enter N, the switch appears as a candidate switch in the Network Assistant GUI. You can configure the switch as a command switch later through the CLI, the device manager, or the Network Assistant application. To configure it later, enter no.

Would you like to enable as a cluster command switch? [yes/no]: no You have now completed the initial configuration of the switch and the switch.

This is an example of the configuration output that appears: The following configuration command script was created: hostname switch1 enable secret 5 $1$Ulq8$DlA/OiaEbl90WcBPd9cOn1 enable password enable_password line vty 0 15 password terminal-password no snmp-server! No ip routing!

Interface Vlan1 no shutdown ip address 10.4.120.106 255.0.0.0! Interface GigabitEthernet1/0/1! Interface GigabitEthernet1/0/2 interface GigabitEthernet1/0/3!! Interface GigabitEthernet1/0/23! End Step 10 These choices appear: [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config.

[2] Save this configuration to nvram and exit. Choose (2) to save the configuration to NVRAM to use it the next time the switch reboots. Enter your selection [2]: 2 Make your selection, and press Return. The switch now runs this default configuration. If you want to change this configuration or perform other management tasks, see the.